Legrand AV3 Uživatelský manuál Strana 1

Procházejte online nebo si stáhněte Uživatelský manuál pro Hardware Legrand AV3. Legrand AV3 User Manual Uživatelská příručka

  • Stažení
  • Přidat do mých příruček
  • Tisk
  • Strana
    / 6
  • Tabulka s obsahem
  • KNIHY
  • Hodnocené. / 5. Na základě hodnocení zákazníků
Zobrazit stránku 0
Products Covered: AV3STC, AV3ATC, AV3ARTTC, AV3CTC, AV3CRTTC, AV3SHTC, AV3ATC-LJB,
AV3ARTTC-LJB, AV3ATCLJB25 & AV3ARTTCLJB25.
CAUTION DO NOT operate tile stripper or resurfacing equipment over top of covers. This may result in damage to the
surface finish of the product.
Suitable for use in air handling spaces in accordance with Sec. 300-22 (C) of the National Electrical Code.
AV3 Poke-Thru Series
INSTALLATION INSTRUCTIONS
Installation Instruction No.: 1 003 904 – April 2004
Walker
®
electrical systems conform to and should be properly grounded
in compliance with requirements of the current National Electrical Code
or codes administered by local authorities.
All electrical products may present a possible shock or fire hazard if
improperly installed or used. Walker electrical products may bear the
mark as UL Listed and/or Classified and should be installed in
conformance with current local and/or the National Electrical Code.
24" [610mm] Min
Center – Center
7"
[178mm]
CAUTION: Be certain to drill hole at least 4" [102mm] from any wall or
pillar to leave enough room for Poke-Thru cover assembly.
CAUTION: For tile installations up to a maximum of
3/4" [19.1mm] thick.
NOTE: For tile thickness greater than 3/4" [19.1mm]
consult factory.
IMPORTANT: Please read all instructions
before beginning.
CAUTION: Spacing is limited to no more than one hole per each
65 sq. ft. [6 sq. m] of floor area in each span.
Step 2 Remove 7" dia. [178mm] section from carpet
or tile. Use template provided.
Step 1 Layout and locate position of hole(s).
Step 3 Core drill hole.
CAUTION: Poke-Thru cannot be rotated in
hole after insertion into floor.
4" [102mm] Diameter Core Drill
4 1/16" [103mm] Actual Diameter
Push Down
#6-32 x 1/4" FHMS
three (3) required
Step 4 Stem Assembly:
Catalog No. AV3STC
Insert stem into hole.
Step 5 Cover Assembly:
Catalog No. AV3CTC.
Remove disposable plate
and replace with carpet/tile
flange. Install with three (3)
#6-32 x 1/4" [6.4mm] FHMS.
Zobrazit stránku 0
1 2 3 4 5 6

Shrnutí obsahu

Strany 1 - AV3 Poke-Thru Series

Products Covered: AV3STC, AV3ATC, AV3ARTTC, AV3CTC, AV3CRTTC, AV3SHTC, AV3ATC-LJB, AV3ARTTC-LJB, AV3ATCLJB25 & AV3ARTTCLJB25.CAUTION DO NOT operat

Strany 2

CONVENTIONAL WIRING SCHEMATIC ISOLATED GROUND WIRING SCHEMATICBLACK or HOT BLACK BLACK or HOT BLACKFrom branch circuit from Poke-Thru receptacle From

Strany 3

3Extron Device(Not Supplied)CAUTION: Empty communication ports must be closed off with foam blocks, TracJack blanks or Extron Single and/or Double MAA

Strany 4

4Slide Cover Mounting ScrewsTwo (2) #6-32Align gasket overreceptacle andpress bead intoflange channel.Push DownOnce Poke-Thru is pushedinto the Cored

Strany 5

The AV3TC Series Poke-Thru Devices are UL Listed and Classified to U.S. and Canadian safety standards to the following conditions:The AV3STC Poke-Thru

Strany 6 - Carpet Cutout Template

The Wiremold Company U.S. and International: 60 Woodlawn Street • West Hartford, CT 061101-800-621-0049 • FAX 860-232-2062 • Outside U.S.: 860-2

Komentáře k této Příručce

Žádné komentáře